1 files changed, 172 insertions, 0 deletions
diff --git a/linux/src/drivers/net/eth82586.h b/linux/src/drivers/net/eth82586.h
new file mode 100644
index 00000000..c2178ffa
--- /dev/null
+++ b/linux/src/drivers/net/eth82586.h
@@ -0,0 +1,172 @@
+/*
+ * eth82586.h: Intel EtherExpress defines
+ *
+ * Written 1995 by John Sullivan
+ * See eexpress.c for further details
+ * documentation and usage to do.
+ */
+
+/*
+ * EtherExpress card register addresses
+ * as offsets from the base IO region (dev->base_addr)
+ */
+
+#define DATAPORT 0x0000
+#define WRITE_PTR 0x0002
+#define READ_PTR 0x0004
+#define SIGNAL_CA 0x0006
+#define SET_IRQ 0x0007
+#define SM_PTR 0x0008
+#define MEM_Ctrl 0x000b
+#define MEM_Page_Ctrl 0x000c
+#define Config 0x000d
+#define EEPROM_Ctrl 0x000e
+#define ID_PORT 0x000f
+
+/*
+ * offset to shadowed memory, 0 <= x <= 31. We don't use this yet,
+ * but may in the future. Is shadow memory access any faster than
+ * dataport access?
+ */
+#define SM_ADDR(x) (0x4000+((x&0x10)<<10)+(x&0xf))
+
+/* Always mirrors eexp-memory at 0x0008-0x000f */
+#define SCB_STATUS 0xc008
+#define SCB_CMD 0xc00a
+#define SCB_CBL 0xc00c
+#define SCB_RFA 0xc00e
+
+
+
+/*
+ * card register defines
+ */
+
+/* SET_IRQ */
+#define SIRQ_en 0x08
+#define SIRQ_dis 0x00
+
+/* Config */
+#define set_loopback outb(inb(ioaddr+Config)|0x02,ioaddr+Config)
+#define clear_loopback outb(inb(ioaddr+Config)&0xfd,ioaddr+Config)
+
+/* EEPROM_Ctrl */
+#define EC_Clk 0x01
+#define EC_CS  0x02
+#define EC_Wr  0x04
+#define EC_Rd  0x08
+#define ASIC_RST 0x40
+#define i586_RST  0x80
+
+#define eeprom_delay() { int _i = 40; while (--_i>0) { __SLOW_DOWN_IO; }}
+
+/*
+ * i82586 Memory Configuration
+ */
+
+/* (System Configuration Pointer) System start up block, read after 586_RST */
+#define SCP_START 0xfff6
+
+
+/* Intermediate System Configuration Pointer */
+#define ISCP_START 0x0000
+/* System Command Block */
+#define SCB_START 0x0008
+
+/*
+ * Start of buffer region. If we have 64k memory, eexp_hw_probe() may raise
+ * NUM_TX_BUFS. RX_BUF_END is set to the end of memory, and all space between
+ * the transmit buffer region and end of memory used for as many receive buffers
+ * as we can fit. See eexp_hw_[(rx)(tx)]init().
+ */
+#define TX_BUF_START 0x0100
+#define TX_BUF_SIZE ((24+ETH_FRAME_LEN+31)&~0x1f)
+#define RX_BUF_SIZE ((32+ETH_FRAME_LEN+31)&~0x1f)
+
+
+
+/*
+ * SCB defines
+ */
+
+/* these functions take the SCB status word and test the relevant status bit */
+#define SCB_complete(s) ((s&0x8000)!=0)
+#define SCB_rxdframe(s) ((s&0x4000)!=0)
+#define SCB_CUdead(s) ((s&0x2000)!=0)
+#define SCB_RUdead(s) ((s&0x1000)!=0)
+#define SCB_ack(s) (s & 0xf000)
+
+/* Command unit status: 0=idle, 1=suspended, 2=active */
+#define SCB_CUstat(s) ((s&0x0300)>>8)
+
+/* Receive unit status: 0=idle, 1=suspended, 2=out of resources, 4=ready */
+#define SCB_RUstat(s) ((s&0x0070)>>4)
+
+/* SCB commands */
+#define SCB_CUnop     0x0000
+#define SCB_CUstart   0x0100
+#define SCB_CUresume  0x0200
+#define SCB_CUsuspend 0x0300
+#define SCB_CUabort   0x0400
+
+/* ? */
+#define SCB_resetchip 0x0080
+
+#define SCB_RUnop     0x0000
+#define SCB_RUstart   0x0010
+#define SCB_RUresume  0x0020
+#define SCB_RUsuspend 0x0030
+#define SCB_RUabort   0x0040
+
+
+/*
+ * Command block defines
+ */
+
+#define Stat_Done(s)   ((s&0x8000)!=0)
+#define Stat_Busy(s)   ((s&0x4000)!=0)
+#define Stat_OK(s)     ((s&0x2000)!=0)
+#define Stat_Abort(s)  ((s&0x1000)!=0)
+#define Stat_STFail    ((s&0x0800)!=0)
+#define Stat_TNoCar(s) ((s&0x0400)!=0)
+#define Stat_TNoCTS(s) ((s&0x0200)!=0)
+#define Stat_TNoDMA(s) ((s&0x0100)!=0)
+#define Stat_TDefer(s) ((s&0x0080)!=0)
+#define Stat_TColl(s)  ((s&0x0040)!=0)
+#define Stat_TXColl(s) ((s&0x0020)!=0)
+#define Stat_NoColl(s) (s&0x000f)
+
+/* Cmd_END will end AFTER the command if this is the first
+ * command block after an SCB_CUstart, but BEFORE the command
+ * for all subsequent commands. Best strategy is to place
+ * Cmd_INT on the last command in the sequence, followed by a
+ * dummy Cmd_Nop with Cmd_END after this.
+ */
+#define Cmd_END     0x8000
+#define Cmd_SUS     0x4000
+#define Cmd_INT     0x2000
+
+#define Cmd_Nop     0x0000
+#define Cmd_SetAddr 0x0001
+#define Cmd_Config  0x0002
+#define Cmd_MCast   0x0003
+#define Cmd_Xmit    0x0004
+#define Cmd_TDR     0x0005
+#define Cmd_Dump    0x0006
+#define Cmd_Diag    0x0007
+
+
+/*
+ * Frame Descriptor (Receive block) defines
+ */
+
+#define FD_Done(s)  ((s&0x8000)!=0)
+#define FD_Busy(s)  ((s&0x4000)!=0)
+#define FD_OK(s)    ((s&0x2000)!=0)
+
+#define FD_CRC(s)   ((s&0x0800)!=0)
+#define FD_Align(s) ((s&0x0400)!=0)
+#define FD_Resrc(s) ((s&0x0200)!=0)
+#define FD_DMA(s)   ((s&0x0100)!=0)
+#define FD_Short(s) ((s&0x0080)!=0)
+#define FD_NoEOF(s) ((s&0x0040)!=0)